||This article includes a list of references, but its sources remain unclear because it has insufficient inline citations. (June 2010) ( Learn how and when to remove this template message)|
|Ground testing the X-18 tiltwing|
|Designer||Stanley Hiller Jr|
|First flight||24 November 1959|
|Status||Aircraft scrapped 1964|
The Hiller X-18 was an experimental cargo transport aircraft designed to be the first testbed for tiltwing and VSTOL (vertical/short takeoff and landing) technology.
Design work started in 1955 by Stanley Hiller Jr and Hiller Aircraft Corporation received a manufacturing contract and funding from the U.S. Air Force to build the only X-18 ever produced, serialled 57-3078. 
To speed up construction and conserve money the plane was constructed from scavenged parts including a Chase YC-122C Avitruc fuselage, 49-2883,  and the turboprops came from the Lockheed XFV-1 and Convair XFY-1 Pogo experimental fighter programs. The tri-bladed contra-rotating propellers were a giant 16 ft (4.8 m) across. The Westinghouse turbojet engine had its exhaust diverted upwards and downwards at the tail to give the plane pitch control at low speeds. Hiller nicknamed their X-18 the Propelloplane for public relations purposes. 
Preliminary testing occurred at Moffett Field Naval Air Station, CA. The first flight (hop) was on 11/20/1959 followed by the first real flight on 11/24/1959 with Hiller test pilots George Bright and Bruce Jones.  Further test flights were held at Edwards AFB, ultimately recording 20 flights. A number of problems plagued the X-18 including being susceptible to wind gusts when the wing rotated, acting like a sail. In addition the turboprop engines were not cross-linked, so the failure of one engine meant the airplane would crash. Thrust control was through throttle changes, which were too slow for acceptable height and roll control.
On the 20th and final flight in July 1961, the X-18 had a propeller pitch control problem when attempting to convert to a hover at 10,000 ft and went into a spin. The crew regained control and landed, but the X-18 never flew again. However ground testing of the tiltwing concepts continued. Eventually a VTOL Test Stand was built on which the X-18's vertical takeoff and landing and hover control was to be tested. One engine run was successfully conducted to the full 15-foot wheel height on the VTOL Test Stand. The program was cancelled on January 18, 1964 before further VTOL Test Stand testing could be conducted, and the X-18 was cut up for scrap.
The program proved several things that contributed to further tilt-wing VSTOL technology programs:
- cross-shafting between the engines was necessary in order to avoid loss of control in the event of an engine failure.
- direct propeller pitch control was necessary for precise height and lateral control during VTOL and hover.
This knowledge was employed in the successful development and flight tests of the Tri-Service XC-142A, tilt-wing VSTOL transport.
- Crew: 2-3
- Length: 63 ft 0 in (19.2 m)
- Wingspan: 47 ft 11 in (14.6 m)
- Height: 24 ft 7 in (7.5 m)
- Empty weight: 26,786 lb (12,150 kg)
- Max takeoff weight: 33,000 lb (14,969 kg)
- Powerplant: 2 × Allison T40-A-14 coupled turboprop engines, 5,500 hp (4,100 kW) each
- Powerplant: 1 × Westinghouse J34 turbojet, 3,400 lbf (15 kN) thrust for reaction jet pitch control
- Propellers: 6-bladed Aeroproducts, 14 ft (4.3 m) diameter contra-rotating propellers
- Maximum speed: 253 mph (407 km/h; 220 kn)
- Service ceiling: 35,300 ft (10,759 m)
HILLER X-18 INFORMATION
POPULAR VIDEOS AND PHOTOS
POPULAR ONLINE SOURCESGoogle | Yahoo | Bing | DuckDuckGo | Ask | Aol | Facebook | Twitter | Linkedin | The New York Times | Yelp | Buzzfeed | US Weekly | RollingStone | WebMD | The Verge | HubPages | PlayBuzz | ESPN